780.20: 1094 Session 14
Handouts: Excerpts on autocorrelation functions
and variational Monte Carlo, printouts
In this session, we'll continue our survey of Monte Carlo computational
methods with a look at autocorrelation
and variational Monte Carlo applied to simple problems.
The discussion is easily generalized to the more complex problems
for which these approaches are well suited.
When evaluating an average over Monte Carlo configurations,
we want to skip the first n1 steps and then use data taken
every n0 Monte Carlo steps. How do we determine how large
to take n0 and n1?
We'll use a simple integration problem to explore these issues,
by integrating x2e-x2
from 0 to 10 and dividing by the integral of e-x2
(so this is like < x2 > with
a probability distribution proportional to e-x2).
- Calculate the (normalized) integral in Mathematica for
- Consider first random sampling as a review/recap of our discussions.
- Run the autocorrelation_test.cpp
code a number of times (at least 10)
and see how the random sampling estimates
vary. Is the calculation of errors in the code (e.g.
with the discussion in the background notes from Session 12d?
Are the estimated errors consistent with the actual deviations
of the estimates from the exact result?
(E.g., if the error is one standard deviation, about what fraction
of the results should lie between the exact result +/- the error?
What fraction do you observe?)
- Vary the number N of configurations used to make the
estimates to see how the error scales.
(The number of configurations
is just the number of x's sampled in this case.)
With what power of N does it scale?
Is this result consistent with expectations from the notes?
- Next consider the Metropolis algorithm. There are three
parameters for you to adjust (besides the total number of iterations):
"max_step", "initial_skip" and "skip".
- What do each of these affect?
(Why do we skip steps at the beginning? Why do we skip
configurations? How do we know how much to change x?
See the Pang excerpt for answers, but discuss it first.)
- Adjust "max_step" so the acceptance rate is around 50% (or
less). [If stepping a vector X, we test every component to form a
Monte Carlo step and look for choosing a step size so that the
acceptance rate is around 50%.] What "max_step" did you
- Devise a way to decide on the "initial_skip" (use a
plot). Set "initial_skip" in the code to the value you deduce.
(Note that your result will depend on your choice of "max_step".)
Explain your value.
- To figure out a good value for "skip", we'll calculate the
"autocorrelation function". This is defined in the Pang handout
as equation (9.21). For us, "A" is "x2". Your task
is to generate the analog of Fig. 9.1.
- What is the value of
the autocorrelation function C(l) at l=0?
- What is the condition that makes C(l) tend to zero (based
on the defining equation)?
- You have everything you need in the code already for (9.21)
except for the average in (9.22). Modify the code to
calculate that and then print out and plot C(l). Attach the plot.
[Hint: An easy way (although not the most efficient way!)
is to introduce an array "result_save[i]" in the Monte Carlo
step loop and save all of the "result" evaluations.
Then after this loop you can step through values of l (say from
0 to 100) and calculate (9.22) for each l (you should only use
iterations - l configurations to do this calculation; why?).
Then you can calculate (9.21) and output it.]
- Now that the Metropolis results are reliable, repeat step 2.
above, but now for the Metropolis sampling.
What do you find?
Variational Monte Carlo
We'll do a simple example of variational Monte Carlo to illustrate
the basic idea. Generalizing to more complex systems is straightforward
(but takes a lot longer to run!).
- Take a look at the "variational_SHO.cpp" code and see how it
implements variational Monte Carlo for a one-dimensional harmonic
oscillator using the VariationalMC class.
Compile, link, and run it (there is a makefile). What is
the trial wave function? Why is this a reasonable one to use?
You'll be asked to supply
a range and step size for the variational parameter "a". This will
require some experimentation to make sure the minimum with respect to
"a" is in the interval you select.
- The variational_SHO.dat file is suitable for plotting in gnuplot.
The plotfile "variational_SHO.plt" is provided to
plot it with error bars.
Try it out a few times each with 100, 1000, 10000 steps
(attach a plot with a sample result).
Does the graph make sense for a variational calculation?
What about the error bars?
How might you modify the code to
find the minimum automatically (rather than
- Does this code implement all the features explored
in the "Autocorrelation" section? If not, how would you improve
780.20: 1094 Session 14.
Last modified: 01:53 pm, March 03, 2010.