6810: 1094 Activities 14
In this session, we'll continue our survey of Monte Carlo computational
methods with a look at autocorrelation
and variational Monte Carlo applied to simple problems that are
easily generalized.
Autocorrelation
When evaluating an average over Monte Carlo configurations,
we want to skip the first n1 steps and then use data taken
every n0 Monte Carlo steps. How do we determine how large
to take n0 and n1?
We'll use a simple integration problem to explore these issues,
by integrating x^{2}e^{x2}
from 0 to 10 and dividing by the integral of e^{x2}
(so this is like < x^{2} > with
a probability distribution proportional to e^{x2}).
 Calculate the (normalized) integral in Mathematica for
reference. Answer:
 Consider first random sampling as a review/recap of our discussions.
 Run the autocorrelation_test.cpp
code a number of times (at least 10)
and see how the random sampling estimates
vary. Is the calculation of errors in the code (e.g.
error_random) consistent
with the discussion in the background notes from Session 12e?
Explain.

Are the estimated errors consistent with the actual deviations
of the estimates from the exact result?
(E.g., if the error is one standard deviation, about what fraction
of the results should lie between the exact result +/ the error?
What fraction do you observe?)
 Vary the number N of configurations used to make the
estimates to see how the error scales.
(The number of configurations
is just the number of x's sampled in this case.)
With what power of N does it scale?
Is this result consistent with expectations from the notes?
 Next consider the Metropolis algorithm. There are three
parameters for you to adjust (besides the total number of iterations):
"max_step", "initial_skip" and "skip".
 What do each of these affect?
(Why do we skip steps at the beginning? Why do we skip
configurations? How do we know how much to change x?
See the Session 14 notes for answers.)
 Adjust "max_step" so the acceptance rate is around 50% (or
less). [If stepping a vector X, we test every component to form a
Monte Carlo step and look for choosing a step size so that the
acceptance rate is around 50%.] What "max_step" did you
use?
 Devise a way to decide on the "initial_skip" (use a
plot). Set "initial_skip" in the code to this value.
(Note that your result will depend on your choice of "max_step".)
Explain your value.
 To figure out a good value for "skip", we'll calculate the
"autocorrelation function". This is defined in the Session notes
as equation (14.2). For us, "A" is "x^{2}". Your task
is to generate a figure like the one in the notes.
 What is the value of
the autocorrelation function C(l) at l=0?
 What is the condition that makes C(l) tend to zero (based
on the defining equation)?
 You have everything you need in the code already for (14.2)
except for the rightmost average. Modify the code to
calculate that and then print out and plot C(l). Attach the plot.
[Hint: An easy way (although not the most efficient way!)
is to introduce an array "result_save[i]" in the Monte Carlo
step loop and save all of the "result" evaluations.
Then after this loop you can step through values of l (say from
0 to 100) and calculate (14.2) for each l (you should only use
[iterations  l] configurations to do this calculation; why?).
Then you can calculate (14.2) and output it.]
 Now that the Metropolis results are reliable, repeat step 2.
above, but now for the Metropolis sampling.
What do you find?
Variational Monte Carlo
We'll do a simple example of variational Monte Carlo to illustrate
the basic idea. Generalizing to more complex systems is straightforward
(but takes a lot longer to run!).
 Take a look at the "variational_SHO.cpp" code and see how it
implements variational Monte Carlo for a onedimensional harmonic
oscillator using the VariationalMC class.
Compile, link, and run it (there is a makefile). What is
the trial wave function? Why is this a reasonable one to use?

You'll be asked to supply
a range and step size for the variational parameter "a". This will
require some experimentation to make sure the minimum with respect to
"a" is in the interval you select.
 The variational_SHO.dat file can be plotted in gnuplot.
The plotfile "variational_SHO.plt" is provided to
plot it with error bars.
Try it out a few times each with 100, 1000, 10000 steps
(attach a plot with a sample result).
Does the graph make sense for a variational calculation?
What about the error bars?
How might you modify the code to
find the minimum automatically (rather than
graphically)?
 Does this code implement all the features explored
in the "Autocorrelation" section? If not, how would you improve
this code?
 Bonus: The trial function is too good a guess.
Try modifying it to another reasonable form
with one variational parameter "a" (use your
imagination!). You'll have to modify the "Psi" and "E_local"
functions. Find the minimum graphically and compare to the
exact solution.
Checking for Bad Input Values
You may have noticed that the nonlinear pendulum codes with the
menus went crazy if you accidently typed a letter or a symbol rather
than an integer. Here we see how to avoid this.
 Use make_input_check to create input_check and run it.
First try some integers and then 1 to see how it is supposed to
work. Then restart it and put in a letter or symbol (or whatever you
want). To stop it, use Ctrlc.
 A fix is given in input_check_fixed (which has its own
makefile). Try it out. Look at the printout or on the screen to
see what was done.
What was done to fix it?
6810: 1094 Session 14.
Last modified: 07:49 am, April 03, 2017.
furnstahl.1@osu.edu